### Biodiesel Plant 15 MGY ### Biodiesel plant with nameplate rating at 15 MGY (million gallons per year). Was designed to run soybean oil and was in operation on crude degummed oil. Complete plant is available - must be relocated. Does not include electrical. The entire plant is inside in a protected building except for the methanol distillation column. Allen Bradley plc controls. Still installed. Plant never met nameplate capacity but average rate was between 6 to 8.7 MGY. In operation from 2020 to late 2021. Includes all in-process tanks, The 18 outside storage tanks are available on Asset 2365 and Asset 2366. We have details and drawings in our Virtual Data Room (VDR) - available upon invitation. - (3) biodiesel reactors - (3) horizontal settling tanks - Glycerin coalescer distillation column - Biodiesel coalescer distillation - MRU methanol recovery unit distillation column & system - Cold soak filtration system - Vertical pressure leaf filter and (2) plate and frame filters including slurry and earth handing systems - (2) Hydrasep oil water separators - Air compressors, pumps, heat exchangers - Allen Bradley controls, HMI

### Biodiesel Plant - 3 MGY (million gallons per year) ### Manufactured by Greenline, this plant ran cottonseed oil in a continuous flow, water free, transesterification reaction and separation modules. - On skids and includes in-process tanks. - Fully automatic with plc control; all controls are still there and intact except for the HMI. - No tank farm - No air compressor - This plant was just inspected by the manufacturer in Dec 2021 and all pieces are still there except for some water piping. - The manufacturer notes that this plant is in good condition and very little CapEx will be needed to start the equipment back up. Customer will have to make its own determination. - Plant must move. - Approx space is occupies now is 75 ft x 100 ft Started in 2008 - idled in 2010. We can offer two further options at an additional price: 1. Greenline refurbish all equipment and make ready for start-up. 2. Greenline install and start-up equipment at new location. See information in Links; more data in our Virtual Data Room (VDR).

Biodiesel Plant nameplate capacity 5 MGY (million gallons per year). Design is super critical reactor type, developed by Jatro Renewables. This design technology allows this plat to handle very dirty high ffa feedstock while operating cheaper than a conventional catalyst biodiesel plant. No toxic catalyst. Output biodiesel is much clearer than conventional biodiesel. See our marketing deck for lengthier explanations. No license fees. All assets are for sale as an entity - must be relocated. All structure included - building is not included. Includes lab equipment. See Marketing Deck general arrangement in Link. Operated from Nov 2015 to 2019 - now idle.

### Crush Plant - Mobile. Capacity 40 TPD (tons per day) ### Capacity 40 TPD or 3600 pounds per hour mobile mechanical pressing/crushing plant built into semi-trailer. This unit has very few hours. Built June 2020 and ran until Aug 2021. The Processing unit extrudes and presses soybeans (or oilseeds) into soybean meal and oil. It is an operational self-contained unit with process controls in a 53’ van trailer. It has a rated processing capacity of 3600 lbs. of soybeans per hour. The unit has 2 extruders, 2 presses, a cooling drum, roller mill, oil recycling system, oil storage tank and conveying and process control equipment. Power: 480 volt 3-phase for connected load 350 HP total; can use Generator or Grid power. The extruders are in the rear of the trailer, presses in the middle, then the cooling drum and roller mill going forward. Soybeans drop into the extruders from the top of the trailer. The meal exits the side after the roller mill. The oil storage tank is in the front of the trailer. Oil can be pumped straight out the side to a tanker or to the front storage tank. We used the storage tank in the winter and pumped straight into the tanker in the warmer months. Tractor (on trailer) and sheds in back are not included. See flyer with Equipment List in Links Overview. The extruders are in the rear of the trailer, presses in the middle, then the cooling drum and roller mill going forward. Soybeans drop into the extruders from the top of the trailer. The meal exits the side after the roller mill.

### Edible Oil Refining Plant 550 TPD### - This plant has been recently idled - essential personnel are still there. Added capability for soybean refining and enzymatic degumming. Mainly automatic with plc controls. Plant is currently idle but Plant Manager, Lead Operator, and Logistics Manager are still there maintaining the equipment including turning large motors. Electricity still on and all permits are current. Data room available upon request after signed NDA. ***Includes*** - 1.3 million gallons of storage - Barge dock on Mississippi River - Automatic with PLC controls - Full Lab - 53 acres of land - Rail access (CN) ***Overview*** - This plant started transesterification biodiesel production 2007 with a name plate capacity of 72 million gallons per year and demonstrated production of 63 million gallons per year. Feedstock was solely Crude Degummed soybean oil, and finished product met or exceeded ASTM D6751. - In 2022 the plant was converted to refine soybean oil frome crude or crude degummed soybean oil. The refining process was designed for 144,000 gallons per day, max demonstrated production was 86,000 gallons per day. Refined soy oil processed was sold to Renewable Diesel producers, our refined oil sold met or exceeded all parties required specification. The actual COA’s are in the virtual data room - In August 2023, production ceased and the plant was shut down. Critical operations team still in place.

Biomass drying and ethanol solvent extractor system, last used for producing CBD Extract by drying hemp at 3,000 #/day infeed and approximately 1,000 #/day dry mass outlet. Was running hemp with infeed moisture of 50-80% and outlet moisture of 7% to 11% moisture. CBD extraction efficiency is very good. Complete line was purchased new in 2019 - only has 1,289 hours operation. Main components include Gryphon gas fired dryer, ribbon blender, Watermark filter press system, Nutsche filter, BizzyBee distillation system, tanks (missing Vincent dewatering press). See Links for equipment list and process flow chart.For all components enter the key word pk6020 in search box..

Hydrogen generating plant rated at 7 MM SCFD (million standard cubic feet per day or 16.5 TPD). Reconditioned w/ warranty. Pressure at PSA of 200 psig then gas compression to 650 psig. H2 steam methane reformer design (SMR). Nearly NEW and lightly used. Plant can handle a turndown rate from 4 MM to 7 MM SCFD. Steam export 13,000 lb/hr. Designed to meet California's regulations. Plant is offered removed, reconditioned, with EPC and supervision for installation (installation labor by customer - all obligations clearly listed in the proposal document). Full Presentation Proposal document available on request with NDA including entry into data room. Natural gas fired 450 psig, H2 production at 200 psig of 99.99% pure hydrogen. Plant originally ran in Oklahoma in 2018 for 6 months and has now been removed and stored in Houston. Was operating as a syngas generation plant but will be modified by adding a Water Gas Shift unit, an optional Pre-Reformer unit (added cost) and a Pressure Swing Adsorption unit. First year spare parts and annual maintenance parts included. Allow time to engineer and recondition - Warranty and Process Guarantee provided.

### Hydrogen Generating Plant (partial) ### - Design capacity is 90,000 scfh at 200 psig with a purity of 99.99% pure hydrogen - was running on 10 of its 20 tubes for 45,000 scfh capacity. Burner has been changed out to run the 45,000 scfh capacity. - Reformer can be fired on natural gas or propane - same burner. - Waste heat boiler generating 3,000 to 5,000 #/hr export steam at 250 psig. - PSA plant (4 psa vessels replaced in 1998) with Jamesbury valves kept up to date, Quench pot design. - Plant is missing small natural gas compressor, heat exchangers, and pumps. - Has new tubes, new reformer, and new shift converter catalyst. - Five (5) spare tubes available. Engineered by Hydro-Chem built in 1980. . Plant was shut down in mid 2012, and proper shutdown procedures were followed. Reformer tubes are 6.625" OD, 5.25" ID, 30.825" long and made of alloy HP50 (also known as 25/35)

### Vincent Fiber Filter Sludge Press 300-1500 gpm ### Sludge Press manufactured by Vincent. Model EF-30. Stainless Steel, serial number 17590-8. 30HP with a capacity of 300-1500 gpm. Built in 2019 and is presently installed in operation. Serial 17590-8 (Se fiber filter model FF-30) Featuring fine filtration of high gpm throughputs, the Fiber Filter is a unique machine. It operates continuously with a fabric filter that is vibrated clean by the process flow, requiring only occasional back-flush cycles. Liquid flows with fiber contents ranging from 0.3% to 1.5% are thickened to a range of 4% to 14% solids with the Fiber Filter. The filtrate liquid is remarkably clear. The Fiber Filter can replace equipment ranging from pre-thickening screens to centrifuges. Fiber Filters can be used both to thicken flow ahead of a screw press and to remove fiber from press liquor. Mechanically the Fiber Filter has a rotating paddle impeller that whirls and pulses the incoming fluid against the inside of a cylindrical filter screen. The filter sleeve, held taught in a frame, is made of a woven polymer fabric. The fabric is available in meshes ranging from 25 microns (0.001") to 300 microns (0.012"). Fabric tension is adjusted from outside the machine, improving sanitation and facilitating operation.*

Heyl & Patterson Rotary Railcar Dumper System Designed to handle 3000 TPH. Can purchase outright to relocate. Included - Dumper, 309 ft conveyor, 2 control rooms, building over the dumper, all electrical, dust suppression system. Details - Inclined conveyor capacity 3000 TPH, 72" wide x 309' long at 476 fpm. Roller spacing 1'-0" with 450 HP motor drive. Inclined 16 degrees, length 309'-10-1/4" pulley centers. Also a feeder conveyor 96" wide x 16 ft long at capacity 3000 TPH, Size/Belt Speed 96”/110 FPM- Variable Speed Roller Spacing 1’0” Max HP 125 motor 16’0” Pulley Centers. Hoppers: Dims and Angles 24’ W x 47’ L x 35’ Ht, 74.8 Min Slope, 70 degree Angles Lining 1/2” Tivar 88 Steel Thickness 3/8”. Conveyor is all galvanized, aluminum conduit, walkway on one side, Paramax 9000 gearbox. Railcar Dumper is equipped with ventilation fans, dust suppression system, 5 ton hoist, Hazleton sump pump model 75-350 SHW, Cutler Hammer MCC rated at 2500A horizontal bus 480v 3/60. . Not Included: rotary stacker conveyor shown at end of run. Installed 2010 and idled in 2012 - used approx 2 years.. See videos in Link. The video showing operation is not this one but is typical.

### Distillation System - for Corn Oil/Ethanol/Water Separation ### Skid mounted distillation system designed to remove ethanol and water from corn oil. Design capacity 10 gpm with infeed composition 95% oil and max 5% water/ethanol. Results: Corn oil output with 1000 ppm water max. - NEW - never used. Built 2019 - never commissioned, in protected warehouse - Stainless steel 304L - Includes SRS SRDX-600 flash distiller packed column 3 ft dia x 15 ft tall. Serial number 022619 - Two 150 gallon tanks - Vacuum pump - Two centrifugal pumps - Four plate heat exchangers - Piping and instrumentation. - All components are wired to the control panel on skid, but no plc - Spec'd for 19 gpm of ethanol/water flashed to azeotrope See Links for Equipment List and more details. P&ID available in Virtual Data Room (VDR) - ask for an invitation.

### Distillation System Enhancement - for ffa/Ethanol/Water Separation ### Skid mounted distillation system designed to remove ethanol from water. This skid was designed to be added to back of skid VR2 to further reduce the water content of the ethanol to 500 ppm-1000 ppm range. However, can also be a stand alone skid for reducing water/ethanol in other oil processes. - NEW - never used. Built 2019 - never commissioned, in protected warehouse - Stainless steel 304L - Includes SRS flash distiller column 10 inches dia 12 ft tall, serial number 00619 - One stainless tanks 2 ft dia - Two centrifugal pumps - Two plate heat exchangers - Piping and instrumentation. - All components are wired to the control panel on skid, but no plc - Capacity of VR3 is 3 gpm and is designed to remove <30% ethanol/water from oil down to 1000 ppm. See Links for Equipment List and more details. P&ID available in Virtual Data Room (VDR) - ask for an invitation.

### Ring Dryer, GEA Barr-Rosin ### Used for drying wet cake DDGS but can be used to dry almost anything – such as hemp or other grains. Dries material from 65% moisture to 11% moisture, evap rate 66,463 #/hr. This dryer was designed to handle 112,861 wet infeed at 65% moisture and 440,000 #/hr dry recycle material. This design lends itself well for varying flows and moistures, and precludes clogging or clumping. Comes with Lo-Nox main burner natural gas fired 83 MMBTU, a 1200HP main fan, 2 combustion/exhaust fans 150HP, Fluid Bed Cooler and Baghouse, (2) paddle mixers, (9) drag and screw conveyors, (4) rotary valves, (4) cyclones, disintegrator. Designed for 67,109 #/hr wet grain + 45,752 #/hr syrup IN = 46,398 #/hr OUT Evap rate 66,463 #/hr Fan: 189,339 scfm 1300HP. Burner heat 83.1 MMBTU. See data sheet, P&ID, and GA in Links. Still installed. For list of components and their photos & description enter dr5201 in search box on web site

## Fractionation Systems Pressure 30 bar - for Edible Oil ## - TWO complete systems including all tanks, pumps, heat exchangers, fitters, and controls. Includes all piping and everything in this room. ### 78 MTPD System ### Fractionation system - supplied by DeSmet, rated at 30 bar (450 psig). System built 1997. Includes (18) vertical crystallizers and Industrieterren membrane filter (made in Belgium) with 69 plates polypropylene. Capacity 78 MTPD based on first fractionation Palm Oil – OR - 18 MTPD OUTPUT based on 2nd Fractionation = 10.5 million pounds product + 3.5 million pounds by-product. Capacity will vary depending on type of operation and oil. - Membrane filter for fractionation, made by Industrieterrein Wijngaardveld AALST, Belgium. Serial 150 10. Type OGFP1500, rated at 30 bar. Has 69 plates, 1500mm x 1500mm. Filter cake volume = 2,875 liters (759.5 gallons). Filter area 255 sq m, with 25mm cake per cavity. Automatic with plc operator interface, on-board hydraulic system with dual acting cylinder. J4744 ### 40 MTPD System ### Fractionation system - supplied by DeSmet. System built 2000. Includes (6) vertical ss crystallizers and Filox membrane filter (made in Germany) with 36 plates polypropylene. Capacity 40 MTPD based on 1st fractionation Palm Oil – OR - 5 MTPD OUTPUT based on 2nd Fractionation = 2.5 million pounds product + 1.5 million pounds by-product. Capacity will vary depending on type of operation and oil. Stainless steel trough and auger system. Includes all tanks, pumps, electrical, and control systems. - Filox membrane filter for fractionation, rated at 30 bar (450 psig). Made by Filox - Filtertechnik Gmbh, Germany. Type MKF150-36-250H, serial 2117. Has 36 polypropylene plates, 1500mm section - cake volume 1500 liters, cake thickness 25mm, 40.5 sq m filter surface area. Automatic with plc operator interface, on-board hydraulic system with dual acting cylinder. Hydraulic unit 15HP. Size 6535mm long x 2820mm wide x 2610mm tall, weight empty 34,785 kg. J4747

Slurry tank system consisting of skid with vertical stainless steel tank, (2) Grundfos pumps. SS skid size is 98" x 68" x 84" tall. No agitation - Tank size is 5 ft dia x 6 ft tall for capacity of 850 gallons. Flat bottom, dish top with hinged manway lid. (atmospheric). Grundfos pumps are CRN15-08 A-FGJ-G-E-HOQE. Model A96127009-P11101551 designed for 90 gpm at 528 ft hd. Turning at 3444 rpm. Motor is 15 HP 3500 rpm 460/3/60. Supplies pressing water to Outotec Larox PF1.6 filter system. Part of Outotec Laroc Pressing System